Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
Just about every person maintains their personal opinion about Installing A Bathtub.
Setting up a bathtub isn't specifically brain surgery, yet it does require strong plumbing, woodworking, as well as often, tiling skills. Replacing an old tub with a brand-new one is likewise a reasonably challenging project. If the old tub is readily available, the job can move rapidly; if you have to open up a wall to remove the old bathtub and also position the new bathtub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will need a helper to move out the old bathtub and set in the brand-new one. Ensure you have qualified on your own for the task and are comfortable attempting it. Instead of employing a professional to take over a halfway-completed job, it is much better to consider employing one before you start. Opportunities are you might require a professional plumber to make tube connections.
This article will assist you install a new bathtub in your washroom if you have actually already gotten a new tub and don't require to alter the setup of your previous water pipelines.
Your devices and material list ought to make up the following:
Planning for the Installment
To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the versatile tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath should currently be ready to be suited its last setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your setup, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather problematic as a result of the restricted accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned of any kind of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four small points.
The following objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub until the spirit level reviews level.
To set up faucets, fit all-time low of the furthest flexible tap port to the proper supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water supply and also inspect all joints and brand-new pipework for leaks and tighten them if essential. Fill up the bath tub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, fix the bath paneling as defined in the producer's user's manual. Tiling and also securing around the tub must wait until the bathtub has been made use of at the very least when as this will certainly settle it into its final placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin making sure that the washers are in location between the tap and also the sink. Safeguard the tap in place with the maker supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The former type must be attached to the faucet ends initially, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, causing the water to penetrate the wall surface between the bath and the tiling, causing difficulties with dampness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and also cartridges, as well as can securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always load the bathtub with water prior to sealing, to allow for the movement experienced when the bathtub is in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that piece of content was worth the trouble. Enjoyed our post? Please share it. Let somebody else locate it. I praise you for your time. Visit again soon.
Set Up An Appointment Report this page